New Equipment Installations
Pool Pump Installations
Your Pool Pump Runs More Than Any Other Appliance in Your Home
The pool pump is one of the hardest-working and most expensive-to-run pieces of equipment on your property. If yours is old, undersized, or a single-speed model, you’re likely paying far more in electricity than you need to.
Aqua Pools installs variable-speed pool pumps from the industry’s leading brands, sized correctly for your pool and set up completely before we leave.
Licensed & Insured
CC# 18-SP-20802-X
Why does your pump choice matter?
A pool pump isn’t just a part you replace and forget — it’s the single biggest factor in your pool’s monthly running cost, and Florida’s climate and code requirements make that choice even more important.
- It runs almost every day, year-round. In Florida, pumps typically run 8+ hours a day to keep water properly filtered and circulated — small efficiency differences add up fast on your power bill.
- Single-speed pumps are largely a thing of the past. Federal energy standards and Florida code have phased single-speed motors out of most residential installations — they’re now limited to specific low-horsepower, dedicated-purpose uses rather than as your pool’s main pump.
- The right size matters as much as the right type. An oversized or undersized pump wastes energy and shortens the life of your whole filtration system — sizing is something a licensed installer should calculate, not guess.
- Installation quality affects performance. Plumbing, priming, and electrical connections all affect how efficiently a pump actually runs once it’s in the ground — not just its spec sheet.
WHAT WE INSTALL
Single Speed vs. Variable Speed Pumps
Pool pumps have historically come in two basic types, single speed and variable speed, because pools have two very different demands: constant, low-flow filtration most of the day, and short bursts of higher flow for things like heating or cleaning cycles.
Single-speed motors were built for an era when pumps simply ran at one speed for everything, while variable speed technology was developed specifically to match the pump’s output to what the pool actually needs at any given moment — which is also why the two types now perform so differently on your energy bill and why Florida code treats them differently today.
Single Speed Pumps
Single-speed pumps run at one constant, high RPM the entire time they’re on — there’s no way to slow them down for routine circulation. In Florida, this makes them impractical (and in most cases, non-compliant) as a primary pool pump.
Today, single-speed motors are really only appropriate for specific low-horsepower, dedicated-purpose applications — like a booster pump for a cleaning system or a spa jet pump — not for running your main filtration system.
Variable Speed Pumps
Variable speed pumps let you run your pool at a low, efficient RPM for everyday filtration and only ramp up to higher speeds when you actually need more flow — for example, running a heater or a cleaning cycle. That flexibility is where the real savings come from:
- Lower energy bills. Variable speed pumps use significantly less energy than single-speed models for the same daily filtration — often cutting pump-related electricity costs dramatically over a year.
- Longer equipment life. Running at lower RPM most of the day means less wear on the motor and seals, which typically means a longer service life than a single-speed pump sees.
- Quieter operation. At low speeds, variable speed pumps run noticeably quieter than single-speed motors — most homeowners barely notice them running.
- Code-compliant. Variable speed pumps meet current Florida and federal energy efficiency requirements for residential pool installations.
- Automation-ready. Variable speed pumps can be programmed with custom schedules and speeds, and integrated into a full pool automation system.
Not sure which system fits your setup? That’s exactly what the free on-site assessment below is for — we’ll look at your existing equipment and recommend the right brand, not just the one we’d rather sell.
Brands We Install
We install and service variable speed pumps from the three most trusted names in the pool industry, and we’ll recommend the brand and size that actually fits your pool — not just the one on the truck.
Pump Setup & Automation configuration included
Buying the right pump is only half the job. A variable speed pump only saves you money if it’s actually programmed to run efficiently — and that’s a step a lot of installations skip.
Every pump installation from Aqua Pools includes:
- Custom run schedules — set to your pool’s actual filtration needs, not a generic factory default. We calculate run times based on your pool’s volume, bather load, and equipment, so the pump isn’t running longer (or shorter) than it actually needs to.
- Speed programming — matched to your filter, heater, and any cleaning equipment or water features. Different equipment needs different flow rates to work properly, so we program separate speeds for each function instead of leaving the pump on one setting for everything.
- App and automation setup — if your pump is automation-compatible, we configure it with your Jandy, Pentair, or Hayward app before we leave, so you can adjust it from your phone. That includes setting up your login, naming your equipment in the app, and confirming remote control actually works before we consider the job done.
- In-person walkthrough — we show you how to check and adjust your settings, not just hand you a manual. You’ll know how to change a schedule, override a speed, or check that everything’s running correctly without having to call us for routine adjustments.
Frequently Asked Questions
Can I still install a single-speed pump in Florida?
In most cases, no — not as your main pool pump. Current Florida and federal energy standards effectively require variable-speed (or two-speed) pumps for primary residential pool circulation. Single-speed motors are now limited to specific low-horsepower, dedicated-purpose uses.
How much can I actually save by switching to a variable speed pump?
Savings depend on your pump’s current size, how many hours it runs, and your local electricity rate, but variable speed pumps are widely recognized as one of the highest-return upgrades a pool owner can make. We can walk through your specific numbers during your free assessment.
Do I need a new pump if mine still works?
Not necessarily — if your current pump is a properly sized variable speed model in good condition, replacement may not be needed. We’ll give you an honest assessment rather than a sales pitch.
How long does a pump installation take?
Most residential pump replacements are completed in a few hours, depending on plumbing and electrical conditions on-site.
Will you set up the app and schedules, or do I have to do that myself?
We handle it. Every pump we install is fully programmed and, if applicable, connected to your automation app before we leave — you shouldn’t have to figure that part out on your own.
Does a new pump work with my existing filter and heater?
In most cases, yes — variable speed pumps are designed to integrate with standard filtration and heating equipment. We’ll confirm compatibility during your free assessment.
Get a free estimate
Give us your best contact details, We'll reach you soon!
Contact
(954) 305-9285
Find Us
10873 NW 52nd street, unit #3. Sunrise FL 33351.
Mon-Fri: 9:00 AM – 6:00 PM
Licensed and Insured
CC# 18-SP-20802-X
